给我留言

Product Center

  • Product Name:China Supplier Battery Thermal Shock Test Machine KJX-326

  • Product Model:KJX-326
  • Design Standard:GB 31241-2014,GB/T 18287 -2013,GB/T 8897.6-2008,YD/T 2366.1-2011,GB/T 21966-2008,MT/T 1051-2007
  • Update Time:2017-3-21 15:10:15
  • Click:545

Introduction

Battery Thermal Shock Test Machine KJX-326

 Uses

The battery was placed in a hot box and the temperature was raised to 130 ° C ± 2 ° C at a rate of (5 ± 2 ° C) / min and held for 30 minutes. Then, the solution was returned to room temperature. Test the battery should not fire, do not explode.

 

principle

The instrument built-in forced air circulation, the wind source by the cycle of motor operation to drive the wind turbine through the electric heater, the hot air from the duct to the oven inside, thereby reducing the energy loss and to ensure uniformity of the temperature inside the box, The action can cause the disturbance, the air circulation system can quickly return to the operating state of the temperature value, open the inlet and outlet, the air circulation is smooth, fast ventilation, to avoid the concentration of combustible gas caused by spontaneous combustion explosion.

 

standards

GB  31241-2014,GB/T 18287 -2013,GB/T 8897.6-2008,YD/T 2366.1-2011,GB/T 21966-2008,MT/T 1051-2007,YD 1268-2003,GB/T  19521.11-2005,YDB 032-2009,UL 1662:2012,UL 2056: 2012,UN38.3(2012),IEC62133-2012,IEC 62281: 2006,IEC 60086: 2007 etc.

 

Main features and functions:

1. The temperature control for the PID microcomputer automatic calculation of intelligent temperature control table, PV / SV at the same time display, the machine temperature can be allowed within the scope of the individual free to set the required temperature, and through the table PID parameter settings to ensure that its control Temperature accuracy, but also by the system itself with the self-calculation of the system to get the appropriate temperature control parameters, while the temperature control table can be set to 30 wet procedures to control the heating rate (average wet, non-linear no-load) The The following are the same as the "

2. The temperature into the force CA (K) TYPE temperature head, the output is 12V. The following are the same as the "

3. The current controller for the use of imported SCR solid state relay (SSR) no contact no spark phenomenon, safe and maintain the high stability of the current, through the thermostat signal automatically adjust the output ratio

4. The timer: electronic digital display, the timing of automatic temperature control, temperature to the time, time to cut off the power supply (when the timer switch to the open position, the temperature control on the actual temperature-PV value reaches the set temperature - SV value when the timer starts to work; when the timer time to set the time to cut off the machine when the heat, the motor power and alarm, only to keep the control of the display power and power and speed up the cooling rate, so That is to ensure the accuracy of the work time and save the power loss, but also easy to observe when the work is completed when the temperature inside the box is normal.

5. The structural design features: cold-rolled stainless steel box + insulation cotton + stainless steel plate, while the door is also used in this structure, observe the window of the tempered glass thickening, to prevent possible explosion on the box The destructive power;

6. Explosion-proof door lock: box door explosion-proof door lock, the pressure in the box, can automatically open the door, will not let the strong airflow damage to the door, while the test can be opened after the second door.

 

Specification

Temperature range

Room temperature (or ambient temperature)~ 200

Temperature stability

±0.5℃

Temperature display accuracy

±0.1℃

Temperature distribution uniformity

±2℃

Internal dimensions (width * height * depth)

500*600*500 mm

Heating time

(5±2)℃/min, (Average temperature rise, non-linear no-load)

Temperature table

 

Programmable temperature controller, can achieve the total temperature control time, different from the ordinary temperature control table

Inner box material

stainless steel

Material of outer box

Cold-rolled steel plate paint

Insulation material

Efficient compression of glass wool

Insulation device

No fuse switch, over temperature protection switch, porcelain fuse

using electric

3&,220V,15A, 50HZ

safety devices

The first over-temperature alarm, MCCB overload protection

Exhaust flue

Leaf design adjustable air volume

Control formation

The temperature reaches the set temperature automatically open the time meter, after the time to cut off the heating power, beep tips

Power supply

6KW

Volume (about)

700*600*1320mm (Long * wide * high)

Weight (about)

100kg

 

Battery Thermal Shock Test Machine KJX-326

Battery Thermal Shock Test Machine KJX-326

 

Packaging & Shipping

Battery Thermal Shock Test Machine KJX-326

Production-Process:

Battery Thermal Shock Test Machine KJX-326Battery Thermal Shock Test Machine KJX-326

Company Information

Battery Thermal Shock Test Machine KJX-326

Battery Thermal Shock Test Machine KJX-326Battery Thermal Shock Test Machine KJX-326

Battery Thermal Shock Test Machine KJX-326

 

Certifications

Battery Thermal Shock Test Machine

 

Our Services

Dongguan Kejian Instrument Co., Ltd

 

During the whole business process, we offer Consultative Selling service.


Customer inquiry process:


Discussing testing requirements and technic details, suggested suitable products to customer to confirm. Then quote most suitable price according to customer requirements.


Specifications customize process:


Drawing related drawings to confirm with customer for customized requirements. Offer reference photoes to show the proucts appearance. Then, confirm the final solution and confirm final price with customer.


Order process:


We offer below business term:

Accepted Delivery Terms FOB, CFR, CIF, EXW, DDP
Accepted Payment Currency USD, EUR, HKD, CNY
Accepted Payment Type T/T, L/C, Credit Card, PayPal, Western Union, Cash, Escrow
Nearest Port Shenzhen, Guangzhou, Shanghai, Qingdao, Tianjing or rquired

 
Production and delivery process:


We will produce the machines according to confirmed PO requirements. Offering photoes to show production process.
After finish production, offer photoes to customer to confirm again with the machine. Then do own factory calibration or third party calibration(as customer requirements). Check and test all the details and then arrange packing.
Deliver the products in confirmed shipping time and inform customer.


Installation and after sale service:


Defines installing those products in the field and providing after-sales support.

 

 Battery Thermal Shock Test Machine KJX-326

Our Team:

Battery Thermal Shock Test Machine

 

FAQ

Battery Thermal Shock Test Machine KJX-326

Why choose us?

1. Considerate Service Different countries plugs, manually change the-voltage from 110V to 220V, insurance indicator.

 

2.Excellent after sale service:

1 YEAR warranty. If you have any problems during testing process, we promise we will give you a reply with 24 hours and solution provide within 3 working days. What you need to do is to send us the controller.

 

3.Good Packaging:

Covered with air bubble film before put the machine into the wooden case, which not only has good shock absorption, impact resistance, heat sealing and also has the advantages of nontoxic, odorless, moisture corrosion, good transparency etc.

Related products